The whole series meets 05 grade (Highest Grade) of JIS B 7738 Coil Spring Compression / Tension Tester.
• In addition to 1 Step , 2 -Step, 3 -Step Automatic Tests, Free Length, Initial Tension, Solid Length, Peak Load can be measure.
• Unit select able among N, gf, kgf, lbf and inch covered by English version.
• Measurement range can be changed through 2- step high-low range automatic switch over function, there by eliminating unnecessary steps.
• Dual unit (gf, kgf and N) printing is possible through printer setting. 50 Tests conditon can be store by registering model number.
• Test can start immediately once test condition are recall.
• Passing range or Good / Bad assessment is done visually by using screen display and alarm.
• Can connect to Mitutoyo Digimatic Caliper, Micrometer etc.. And data can be printed out.
• Ascend and descend buttons are equipped with inching function.
• Simple movements of 1mm, 0.1mm, (0.001mm) are possible.

“Load test with length input”, load is measured automatically once length is input. (All-Type)
”Length test with Load input”, spring length is measured automatically once load is input. (S-Type, H-Type)
”Deflection load test”, load is measured automatically based on deflection amount resulted from free length. (S-Type, H-Type)
”Load deflection test”, deflection amount corresponding to applied load resulted from free length is measured automatically.
”Step load test”, load is measured as length is step automatically fixed intervals. (H-Type)
”Step length test”, length is measured as load is step automatically fixed intervals. (H-Type)

Radiographic Testing (RT) is a non-destructive testing (NDT) method which uses X-rays to examine the internal structure of manufactured components to identify any flaws or defects. Microfocus X-ray CT scanning is a 3D non-destructive testing (NDT) technique that allows the testing and 3D analysis of various materials in a non-destructive manner. It is widely used in the measurement of automotive parts, resin molded parts, bones, printed circuit boards (PCB), batteries, polymers, etc.

Shimadzu provides a comprehensive lineup of microfocus X-ray CT systems and solutions for high resolution 3D imaging of a wide variety of samples. Our product lineup includes the XSeeker 8000 bench-top X-ray computed tomography (CT) system, which enables clear observation of metal parts included in compact designs; and the inspeXio 7000 high-performance microfocus X-ray CT system, boasting higher resolution and higher contrast CT images with an intuitive user interface. Learn more about our full lineup below.

Model IT-5 IT-20
Units N.m, kgf.cm, ibf.in
Effective Range +/- 0.02 ~+/- 5.N.m +/- 2 ~ +/- 20N.m
Resolution 0.001N.m 0.01N.m
Accuracy +/- 0.5% of F.S
Maximum Allowable Torque 150%
Maximum Memory Data 511
Comparator Upper & Lower Limit Setting of Specification
A/D Convertor 16 Bit
Response 640Hz/sec
Battery Operated Ni.MH Battery with Power Adaptor
Operating Temperature 10~40 Deg C & Humidity of 85% & Below
Data Output RS232C Interface
Dimension W230 x H60 X D149mm
Mass Approximately 3.3kg

Radiographic Testing (RT) is a non-destructive testing (NDT) method which uses X-rays to examine the internal structure of manufactured components to identify any flaws or defects. Microfocus X-ray inspection is a 3D non-destructive inspection (NDI) technique that allows the testing and 3D analysis of various materials in a non-destructive manner. It is used in a wide range of industries, including the electronics, automotive, semiconductors, and aerospace industries.

Shimadzu provides a comprehensive lineup of microfocus X-ray inspection systems and solutions for high resolution inspection of electronic assemblies, components, and printed circuit boards (PCB). Our product lineup includes the Xslicer SMX-1010/1020, boasting significantly improved image quality and a simplified workflow; and the Xslicer SMX-6010, featuring high-accuracy images with a wide dynamic range that enables detailed observation of internal structures and defects. Learn more about our full lineup below.